11
ноя
Aug 19, 2018 - Zte zxhn h108n firmware update. This is a list of Vulnerabilities for Zxhn h108l firmware (ZTE). Use our CVEMAP to find any issue.
Internet access from providers MTS, Dom.ru and MGTS is provided via a telephone cord. The ADSL technology is used, and the provider can issue a suitable modem / router by itself. In such cases, under MTS Internet, setting up a router is simply setting a login with a password. The bad thing is that the device issued by the provider cannot be connected to the Ethernet line, and nothing other than PPPoE can be used. About setting up one of these routers, ZTE ZXV10 W300, we will talk further. So, the device ZTE W300 performed by 'from the MTS' is equipped with proprietary firmware designed for ADSL connection. Internet connection protocol can be only one - this is “PPPoE + dynamic IP address”.
Before setting up, you need to find out only one thing: what is the address which works on the side of the provider. The numbers of this address are set in the settings of the network card. Now we take a closer look. We connect the router, open the web-interface Inside the device called “ZTE W300”, there is a DHCP server, which is enabled by default. But still, in the parameters of the network card they set a static IP equal to 192.168.1.2: Setting up a wired PC connection The address of the router itself, as you might guess, is 192.168.1.1. This value is set as a gateway, as well as a DNS server (the first). The second DNS server might be: 195.34.32.116.
Nevertheless, different values are used in different regions, pay attention to this. If the network card is configured, any LAN port of the router is connected to the PC using a patch cord. A telephone cable must be connected to the ADSL socket. And the last to connect the power supply. Wait a minute, open a browser on your computer and go to the address of the router (192.168.1.1): ZTE W300 MTS Web Interface The password for the web interface is admin, the same login is used.
Configuring the Internet and 'LAN' First of all, going to the web-interface, it is better to go directly to the following tab: Page 'Application' - u003e 'FON Setting' It is located in the “Application” section and is responsible for the “FON” option (distribution of the Internet to other registered users). By turning off this option and clicking “Submit”, you will protect yourself from unnecessarily annoying “external” users connecting to the Internet from the street. But the provider means that you will not turn off anything (we leave the choice to the owner of the modem). Internet connection, quick setup Go to the “Network” section.
Here we need one tab containing the parameters of the ADSL port: “WAN Connection”, initial state On the tab shown in the example, you can create a new profile (you need to click 'Create'). But it is recommended to use what the provider has already created: select the value “stream” in the upper list. Free plugins for adobe audition. “Stream” profile, MTS connection Connection parameters are chosen as follows: • Enable NAT - enable required; • Enable VLAN - not necessary; • VPI / VCI - 1/50 (specify from the text of the contract); • Encapsulation - LLC; • Service - UBR; • Subscriber's login - see contract; • Password - also specified in the contract; • Authentication type - Auto; • Connection Trigger - Always On. To save the settings, click 'Modify'. In principle, the connection is now configured, and it should automatically become active in a minute (as a result, the “@” light comes on).
If this does not happen, you need to look for an error in the password or login. Now we will look at how to set up IPTV. This is done simply: • Go to the Port Binding tab; • Select the “vod” option in the top list; • Specify the local port on which the TV will go; • Click “Submit”; • Now select the value “m_cast” in the list; • Do steps 3-4; • The value “stream” is selected in the list; • You need to specify the ports that are not used for IPTV, then click 'Submit'. This completes the ADSL port configuration. See an example. IPTV directed to LAN1 Additional options important to the user ICQ and Skype, as well as torrent clients use an option such as UPnP. It needs to be used in the program itself, and in the settings of the router it is available on the following tab: Page 'Application' - u003e 'UPnP' Simply select the value “stream” in the top list, check the box and click “Submit”.
Aug 19, 2018 - Zte zxhn h108n firmware update. This is a list of Vulnerabilities for Zxhn h108l firmware (ZTE). Use our CVEMAP to find any issue.
Internet access from providers MTS, Dom.ru and MGTS is provided via a telephone cord. The ADSL technology is used, and the provider can issue a suitable modem / router by itself. In such cases, under MTS Internet, setting up a router is simply setting a login with a password. The bad thing is that the device issued by the provider cannot be connected to the Ethernet line, and nothing other than PPPoE can be used. About setting up one of these routers, ZTE ZXV10 W300, we will talk further. So, the device ZTE W300 performed by 'from the MTS' is equipped with proprietary firmware designed for ADSL connection. Internet connection protocol can be only one - this is “PPPoE + dynamic IP address”.
Before setting up, you need to find out only one thing: what is the address which works on the side of the provider. The numbers of this address are set in the settings of the network card. Now we take a closer look. We connect the router, open the web-interface Inside the device called “ZTE W300”, there is a DHCP server, which is enabled by default. But still, in the parameters of the network card they set a static IP equal to 192.168.1.2: Setting up a wired PC connection The address of the router itself, as you might guess, is 192.168.1.1. This value is set as a gateway, as well as a DNS server (the first). The second DNS server might be: 195.34.32.116.
Nevertheless, different values are used in different regions, pay attention to this. If the network card is configured, any LAN port of the router is connected to the PC using a patch cord. A telephone cable must be connected to the ADSL socket. And the last to connect the power supply. Wait a minute, open a browser on your computer and go to the address of the router (192.168.1.1): ZTE W300 MTS Web Interface The password for the web interface is admin, the same login is used.
Configuring the Internet and 'LAN' First of all, going to the web-interface, it is better to go directly to the following tab: Page 'Application' - u003e 'FON Setting' It is located in the “Application” section and is responsible for the “FON” option (distribution of the Internet to other registered users). By turning off this option and clicking “Submit”, you will protect yourself from unnecessarily annoying “external” users connecting to the Internet from the street. But the provider means that you will not turn off anything (we leave the choice to the owner of the modem). Internet connection, quick setup Go to the “Network” section.
Here we need one tab containing the parameters of the ADSL port: “WAN Connection”, initial state On the tab shown in the example, you can create a new profile (you need to click 'Create'). But it is recommended to use what the provider has already created: select the value “stream” in the upper list. Free plugins for adobe audition. “Stream” profile, MTS connection Connection parameters are chosen as follows: • Enable NAT - enable required; • Enable VLAN - not necessary; • VPI / VCI - 1/50 (specify from the text of the contract); • Encapsulation - LLC; • Service - UBR; • Subscriber's login - see contract; • Password - also specified in the contract; • Authentication type - Auto; • Connection Trigger - Always On. To save the settings, click 'Modify'. In principle, the connection is now configured, and it should automatically become active in a minute (as a result, the “@” light comes on).
If this does not happen, you need to look for an error in the password or login. Now we will look at how to set up IPTV. This is done simply: • Go to the Port Binding tab; • Select the “vod” option in the top list; • Specify the local port on which the TV will go; • Click “Submit”; • Now select the value “m_cast” in the list; • Do steps 3-4; • The value “stream” is selected in the list; • You need to specify the ports that are not used for IPTV, then click 'Submit'. This completes the ADSL port configuration. See an example. IPTV directed to LAN1 Additional options important to the user ICQ and Skype, as well as torrent clients use an option such as UPnP. It needs to be used in the program itself, and in the settings of the router it is available on the following tab: Page 'Application' - u003e 'UPnP' Simply select the value “stream” in the top list, check the box and click “Submit”.
..." style="letter-spacing:inherit;">Proshivka Modema Ukrtelekom Zte Zxv10 H108l(11.11.2018)Aug 19, 2018 - Zte zxhn h108n firmware update. This is a list of Vulnerabilities for Zxhn h108l firmware (ZTE). Use our CVEMAP to find any issue.
Internet access from providers MTS, Dom.ru and MGTS is provided via a telephone cord. The ADSL technology is used, and the provider can issue a suitable modem / router by itself. In such cases, under MTS Internet, setting up a router is simply setting a login with a password. The bad thing is that the device issued by the provider cannot be connected to the Ethernet line, and nothing other than PPPoE can be used. About setting up one of these routers, ZTE ZXV10 W300, we will talk further. So, the device ZTE W300 performed by 'from the MTS' is equipped with proprietary firmware designed for ADSL connection. Internet connection protocol can be only one - this is “PPPoE + dynamic IP address”.
Before setting up, you need to find out only one thing: what is the address which works on the side of the provider. The numbers of this address are set in the settings of the network card. Now we take a closer look. We connect the router, open the web-interface Inside the device called “ZTE W300”, there is a DHCP server, which is enabled by default. But still, in the parameters of the network card they set a static IP equal to 192.168.1.2: Setting up a wired PC connection The address of the router itself, as you might guess, is 192.168.1.1. This value is set as a gateway, as well as a DNS server (the first). The second DNS server might be: 195.34.32.116.
Nevertheless, different values are used in different regions, pay attention to this. If the network card is configured, any LAN port of the router is connected to the PC using a patch cord. A telephone cable must be connected to the ADSL socket. And the last to connect the power supply. Wait a minute, open a browser on your computer and go to the address of the router (192.168.1.1): ZTE W300 MTS Web Interface The password for the web interface is admin, the same login is used.
Configuring the Internet and 'LAN' First of all, going to the web-interface, it is better to go directly to the following tab: Page 'Application' - u003e 'FON Setting' It is located in the “Application” section and is responsible for the “FON” option (distribution of the Internet to other registered users). By turning off this option and clicking “Submit”, you will protect yourself from unnecessarily annoying “external” users connecting to the Internet from the street. But the provider means that you will not turn off anything (we leave the choice to the owner of the modem). Internet connection, quick setup Go to the “Network” section.
Here we need one tab containing the parameters of the ADSL port: “WAN Connection”, initial state On the tab shown in the example, you can create a new profile (you need to click 'Create'). But it is recommended to use what the provider has already created: select the value “stream” in the upper list. Free plugins for adobe audition. “Stream” profile, MTS connection Connection parameters are chosen as follows: • Enable NAT - enable required; • Enable VLAN - not necessary; • VPI / VCI - 1/50 (specify from the text of the contract); • Encapsulation - LLC; • Service - UBR; • Subscriber's login - see contract; • Password - also specified in the contract; • Authentication type - Auto; • Connection Trigger - Always On. To save the settings, click 'Modify'. In principle, the connection is now configured, and it should automatically become active in a minute (as a result, the “@” light comes on).
If this does not happen, you need to look for an error in the password or login. Now we will look at how to set up IPTV. This is done simply: • Go to the Port Binding tab; • Select the “vod” option in the top list; • Specify the local port on which the TV will go; • Click “Submit”; • Now select the value “m_cast” in the list; • Do steps 3-4; • The value “stream” is selected in the list; • You need to specify the ports that are not used for IPTV, then click 'Submit'. This completes the ADSL port configuration. See an example. IPTV directed to LAN1 Additional options important to the user ICQ and Skype, as well as torrent clients use an option such as UPnP. It needs to be used in the program itself, and in the settings of the router it is available on the following tab: Page 'Application' - u003e 'UPnP' Simply select the value “stream” in the top list, check the box and click “Submit”.
...">Proshivka Modema Ukrtelekom Zte Zxv10 H108l(11.11.2018)